smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.16.5-64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: APPLE HDD ST500LM012 Serial Number: S2XMJ9BD630131 LU WWN Device Id: 5 0000f0 0639b3101 Firmware Version: 2AR30007 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Feb 1 13:16:50 2020 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6420) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 107) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1881 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 092 091 025 - 2507 4 Start_Stop_Count -O--CK 092 092 000 - 8733 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 5522 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 096 096 000 - 4879 12 Power_Cycle_Count -O--CK 092 092 000 - 8907 191 G-Sense_Error_Rate -O---K 100 100 000 - 383 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 056 000 - 26 (Min/Max 17/44) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 4 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 773 223 Load_Retry_Count -O--CK 096 096 000 - 4879 225 Load_Cycle_Count -O--CK 033 033 000 - 683470 254 Free_Fall_Sensor -O--CK 100 100 000 - 970662611783 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbe SL VS 128 Device vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 1812 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1812 [3] occurred at disk power-on lifetime: 5516 hours (229 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 fa b0 00 00 08 fb fc 00 40 00 Error: ICRC, ABRT at LBA = 0x08fbfc00 = 150731776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 01 40 00 00 08 fb fc 30 40 00 00:00:00.037 READ FPDMA QUEUED 60 00 10 08 00 00 00 08 fc 05 70 40 00 00:00:00.037 READ FPDMA QUEUED 60 00 10 08 00 00 00 08 fb fd 70 40 00 00:00:00.037 READ FPDMA QUEUED 60 00 10 08 00 00 00 08 fb f5 70 40 00 00:00:00.037 READ FPDMA QUEUED 60 00 10 08 00 00 00 08 fb ed 70 40 00 00:00:00.037 READ FPDMA QUEUED Error 1811 [2] occurred at disk power-on lifetime: 5514 hours (229 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 10 00 00 00 4d 7b 58 40 00 Error: ICRC, ABRT at LBA = 0x004d7b58 = 5077848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 00 00 4d 7b 58 40 00 00:00:00.005 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 4d 7b 58 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 4d 60 48 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 08 00 00 02 56 82 10 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 4d 7c 78 40 00 00:00:00.006 READ FPDMA QUEUED Error 1810 [1] occurred at disk power-on lifetime: 5513 hours (229 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 10 00 00 05 68 1d 50 40 00 Error: ICRC, ABRT at LBA = 0x05681d50 = 90709328 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 00 05 68 1d 50 40 00 00:00:01.487 READ FPDMA QUEUED 60 00 00 00 10 00 00 05 68 1d 50 40 00 00:00:01.487 READ FPDMA QUEUED 60 00 00 00 10 00 00 05 68 1d 48 40 00 00:00:01.487 READ FPDMA QUEUED 60 00 00 00 10 00 00 05 68 1d 40 40 00 00:00:01.487 READ FPDMA QUEUED 60 00 00 00 10 00 00 05 68 1d 38 40 00 00:00:01.487 READ FPDMA QUEUED Error 1809 [0] occurred at disk power-on lifetime: 5513 hours (229 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 08 00 00 00 4b e7 80 40 00 Error: ICRC, ABRT at LBA = 0x004be780 = 4974464 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 10 00 00 00 4b e7 78 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 10 00 10 00 00 00 4b e7 78 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 10 00 10 00 00 00 07 02 43 40 00 00:00:00.008 READ FPDMA QUEUED 61 00 10 00 10 00 00 00 4b e7 68 40 00 00:00:00.008 WRITE FPDMA QUEUED 60 00 10 00 10 00 00 00 4b e7 68 40 00 00:00:00.008 READ FPDMA QUEUED Error 1808 [7] occurred at disk power-on lifetime: 5476 hours (228 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 08 19 b0 40 00 Error: UNC 8 sectors at LBA = 0x000819b0 = 530864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.593 READ DMA EXT 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.591 READ DMA EXT 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.588 READ DMA EXT 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.586 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:00:03.586 READ LOG EXT Error 1807 [6] occurred at disk power-on lifetime: 5476 hours (228 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 08 19 b0 40 00 Error: UNC 8 sectors at LBA = 0x000819b0 = 530864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.591 READ DMA EXT 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.588 READ DMA EXT 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.586 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:00:03.586 READ LOG EXT 60 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.508 READ FPDMA QUEUED Error 1806 [5] occurred at disk power-on lifetime: 5476 hours (228 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 08 19 b0 40 00 Error: UNC 8 sectors at LBA = 0x000819b0 = 530864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.588 READ DMA EXT 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.586 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:00:03.586 READ LOG EXT 60 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.508 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.583 READ FPDMA QUEUED Error 1805 [4] occurred at disk power-on lifetime: 5476 hours (228 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 08 19 b0 40 00 Error: UNC 8 sectors at LBA = 0x000819b0 = 530864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.586 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:00:03.586 READ LOG EXT 60 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.508 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 08 19 a8 40 00 00:00:03.583 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 23 1f 28 40 00 00:00:03.583 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 23/26 Celsius Lifetime Min/Max Temperature: 15/44 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (91) Index Estimated Time Temperature Celsius 92 2020-02-01 02:40 26 ******* 93 2020-02-01 02:45 31 ************ ... ..( 4 skipped). .. ************ 98 2020-02-01 03:10 31 ************ 99 2020-02-01 03:15 26 ******* 100 2020-02-01 03:20 31 ************ 101 2020-02-01 03:25 34 *************** 102 2020-02-01 03:30 35 **************** 103 2020-02-01 03:35 36 ***************** 104 2020-02-01 03:40 37 ****************** ... ..( 2 skipped). .. ****************** 107 2020-02-01 03:55 37 ****************** 108 2020-02-01 04:00 38 ******************* ... ..( 3 skipped). .. ******************* 112 2020-02-01 04:20 38 ******************* 113 2020-02-01 04:25 37 ****************** ... ..( 3 skipped). .. ****************** 117 2020-02-01 04:45 37 ****************** 118 2020-02-01 04:50 38 ******************* 119 2020-02-01 04:55 37 ****************** 120 2020-02-01 05:00 37 ****************** 121 2020-02-01 05:05 36 ***************** 122 2020-02-01 05:10 34 *************** 123 2020-02-01 05:15 33 ************** 124 2020-02-01 05:20 32 ************* 125 2020-02-01 05:25 26 ******* 126 2020-02-01 05:30 26 ******* 127 2020-02-01 05:35 24 ***** 0 2020-02-01 05:40 25 ****** 1 2020-02-01 05:45 28 ********* 2 2020-02-01 05:50 31 ************ 3 2020-02-01 05:55 33 ************** 4 2020-02-01 06:00 35 **************** 5 2020-02-01 06:05 36 ***************** 6 2020-02-01 06:10 36 ***************** 7 2020-02-01 06:15 36 ***************** 8 2020-02-01 06:20 37 ****************** 9 2020-02-01 06:25 37 ****************** 10 2020-02-01 06:30 37 ****************** 11 2020-02-01 06:35 32 ************* 12 2020-02-01 06:40 26 ******* 13 2020-02-01 06:45 28 ********* 14 2020-02-01 06:50 30 *********** 15 2020-02-01 06:55 31 ************ 16 2020-02-01 07:00 32 ************* 17 2020-02-01 07:05 32 ************* 18 2020-02-01 07:10 31 ************ 19 2020-02-01 07:15 32 ************* 20 2020-02-01 07:20 32 ************* 21 2020-02-01 07:25 31 ************ 22 2020-02-01 07:30 32 ************* 23 2020-02-01 07:35 32 ************* 24 2020-02-01 07:40 33 ************** 25 2020-02-01 07:45 33 ************** 26 2020-02-01 07:50 34 *************** ... ..( 2 skipped). .. *************** 29 2020-02-01 08:05 34 *************** 30 2020-02-01 08:10 33 ************** 31 2020-02-01 08:15 33 ************** 32 2020-02-01 08:20 34 *************** 33 2020-02-01 08:25 34 *************** 34 2020-02-01 08:30 34 *************** 35 2020-02-01 08:35 27 ******** 36 2020-02-01 08:40 31 ************ 37 2020-02-01 08:45 33 ************** 38 2020-02-01 08:50 36 ***************** 39 2020-02-01 08:55 36 ***************** 40 2020-02-01 09:00 34 *************** 41 2020-02-01 09:05 33 ************** 42 2020-02-01 09:10 32 ************* ... ..( 2 skipped). .. ************* 45 2020-02-01 09:25 32 ************* 46 2020-02-01 09:30 30 *********** 47 2020-02-01 09:35 33 ************** 48 2020-02-01 09:40 33 ************** 49 2020-02-01 09:45 32 ************* 50 2020-02-01 09:50 32 ************* 51 2020-02-01 09:55 32 ************* 52 2020-02-01 10:00 31 ************ 53 2020-02-01 10:05 33 ************** ... ..( 2 skipped). .. ************** 56 2020-02-01 10:20 33 ************** 57 2020-02-01 10:25 23 **** 58 2020-02-01 10:30 25 ****** 59 2020-02-01 10:35 26 ******* 60 2020-02-01 10:40 27 ******** 61 2020-02-01 10:45 28 ********* 62 2020-02-01 10:50 28 ********* 63 2020-02-01 10:55 26 ******* 64 2020-02-01 11:00 28 ********* 65 2020-02-01 11:05 28 ********* 66 2020-02-01 11:10 27 ******** 67 2020-02-01 11:15 29 ********** 68 2020-02-01 11:20 31 ************ 69 2020-02-01 11:25 32 ************* 70 2020-02-01 11:30 33 ************** 71 2020-02-01 11:35 34 *************** 72 2020-02-01 11:40 33 ************** 73 2020-02-01 11:45 32 ************* 74 2020-02-01 11:50 31 ************ 75 2020-02-01 11:55 30 *********** 76 2020-02-01 12:00 30 *********** 77 2020-02-01 12:05 30 *********** 78 2020-02-01 12:10 31 ************ 79 2020-02-01 12:15 32 ************* 80 2020-02-01 12:20 32 ************* 81 2020-02-01 12:25 33 ************** 82 2020-02-01 12:30 34 *************** ... ..( 6 skipped). .. *************** 89 2020-02-01 13:05 34 *************** 90 2020-02-01 13:10 25 ****** 91 2020-02-01 13:15 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 32 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific