Skip navigation

New Airport express user needs some help on setup. Thanks

1352 Views 42 Replies Latest reply: Jun 8, 2011 1:05 PM by Tesserax RSS
1 2 3 Previous Next
Merid Level 1 Level 1 (0 points)
Currently Being Moderated
Jun 5, 2011 10:12 AM

Hi all

 

I just bought a airport express and need some help, I have a netgear GT router which has a network cable running downstairs to my airport express which the cable is plugged into.

 

I want to turn on the wifi in the airport express as I am just out of range with my netgear to connect on my iPad.

 

So what do I need to do to leave both wifi options on which  are both cabled together with a network cable so that my iPad can use both wifis

And can I also make it so devices can only connect with a mac code as I use these. For more security.

 

Thanks for any help.

Pc
  • Tesserax Level 8 Level 8 (47,520 points)

    With the AirPort Express Base Station (AX) connected back to the Netgear router by Ethernet, you can configure them both for a "roaming" network.

     

    Roaming Network Setup

    • Ref: See page 42 of the Apple AirPort Networks guide.
    • Setup the Netgear connected to have both NAT & DHCP enabled. This should be its default settings.
    • Setup the AX as a bridge. AirPort Utility > Select the AX > Manual Setup > Internet > Internet Connection > Connection Sharing: Off (Bridge Mode)
    • For each router:
      • Connect to the same subnet of the Ethernet network.
      • Provide a unique Base Station Name.
      • The Network Name (SSID) should be identical.
      • If using security, use the same security type (WEP, WPA, etc.) and password. Note: It is highly recommended that you use WPA2 Personal for best bandwidth performance.
      • Make sure that the channel is set at least three channels apart from the next base station to prevent Wi-Fi interference.

     

    Using MAC filtering is really not a security measure as "hidden" MAC addresses can easily be discovered and bypassed. However, if you feel this is important to you, the AirPorts implement this type of filtering a bit differently than other vendors. That is, the AirPort have an option for Timed Access using MAC filtering which may be a different implementation than your Netgear.

  • lexvo Level 1 Level 1 (60 points)

    I think the solution for you is to set the Airport Express in bridge mode (through Airport Utility).

     

    And you can restrict connection by MAC address through manual setup of the Airport Express.

  • Tesserax Level 8 Level 8 (47,520 points)

    Which version of the AirPort Utility are you using? The latest is: 5.5.2

  • Tesserax Level 8 Level 8 (47,520 points)

    That's the wrong option. The one you want, "Connection Sharing," is on the Internet > Internet Connection tab

     

     

    Connection Sharing.png
  • Tesserax Level 8 Level 8 (47,520 points)

    Ok, here's the shot of my AirPort Express ...

     

    Internet Connection.png

  • Tesserax Level 8 Level 8 (47,520 points)

    This option would only be applicable if you were to extend this AirPort with another. Since this is not the case, you should leave this option disabled.

  • Tesserax Level 8 Level 8 (47,520 points)

    wireless network name (do i pick the same name as the main netgear routers wifi name or a different name as at  the min i have a different name to my netgear router.)

     

    Yes, you want to use the same Network Name (or SSID) at the Netgear's wireless network.

     

    wireless sec: wpa2 pers

     

    password: *** (do i use the same password as my netgear main router ? or a different password)

     

    You want to use the same wireless security type and password as the Netgear's wireless network.

     

    what happens if i use a different uisername and password will it then use a different connection ? i the wifi but if i use the same password and username it will extend my wireless strenth ?

     

    If you configure the AirPort with another Network Name and Security Type/Password, then you will effectively, be running two separate wireless networks.

1 2 3 Previous Next

Actions

More Like This

  • Retrieving data ...

Bookmarked By (0)

Legend

  • This solved my question - 10 points
  • This helped me - 5 points
This site contains user submitted content, comments and opinions and is for informational purposes only. Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use.