Skip navigation

Suggested settings for sharpening and edge sharpening

831 Views 5 Replies Latest reply: Oct 7, 2011 10:18 AM by DougS79 RSS
greg1424 Level 1 Level 1 (0 points)
Currently Being Moderated
Oct 6, 2011 12:21 AM

I recently started using Aperture instead of PSE, the latest issue of PSE is a MAC disaster.

 

The current settings in Aperture for sharpening from camera ?:

Sharpening 0.50

Edges        0.64

Moire         0.50

Radius       4.00

De-noise    0.00

 

When I hit the sharpen and Edge sharpen adjustment button the following is made ;

 

Actual Sharpening :

Intensity         0.5

Radius           1.0

 

Actual Edge Sharpening :

Intensity           0.81

Edges              0.22

Falloff              0.69

 

Are these good and/or decent numbers.

I realize that any picture could require a different setting BUT not fully understanding the aspects of sharpening I can live with an auto adjust.

I would just like to know that these number s will add to the picture.

 

Thanks,

 

Greg

Mac OS X (10.7.1)
  • léonie Level 8 Level 8 (46,510 points)

    Hello Greg,

    that is a very tricky question!

     

     

    First of all: Apple recommends to use "edge sharpening" and not "sharpening" with AP3; the "sharpening" is kept only for compatibility with AP2, so that adjustment made in previous versions still work.

     

    The effect of edge sharpening really depends on your picture, and the defaults are quite good for standard pictures with a decent contrast and little noise.

     

    Unfortunately, you often need the sharpening brush, for example, when it was difficult to take a good shot in the first place - poor light, poor contrast, and a bad signal to noise ratio. Also, Aperture's edge sharpening is not designed to correct unsharpness caused by a wrong focus or small depth of field or motion blur, its only purpose is to mitigate blur caused by the camera’s demosaic filter, but that sould not keep you from using it for other effects too.

     

    What a sharpening filter does, is generally to measure locally the variance in luminance, estimated by the steepness (gradient) of the edge and to emphasize this steepness. The Aperture edge sharpening filter tries to distinguish between luminance variations caused by noise, and luminance variations caused by image structures (edges). The noise reduction filters use the same technique and both filters interact.

     

    The three parameters in the Inspector HUD: As I said, the default settings are not bad for standard situation.

     

    • Intensity: The amount of correction you want - just try it out, it really depends on your taste. Values larger than 0.5 usually will yield results where the adjustment is quite obvious and should be avoided. If this parameter is too high, you will notice contours with a high contrast to be outlined by an extra dark and an extra light line.

     

     

    • Edges: This parameter is a threshold that controls which luminance variations are considered to be edges and which are classified as noise. You will need to adjust this parameter if you are working in noisy regions of your picture, e.g. in very dark regions with poor lighting, or if the camera was set to very high sensitivity. If this value is too high, most pixels will qualify as edges and you will emphasize the noise, if this parameter is set to zero, then no pixels will be enhanced.

     

     

    • Falloff: The edge sharpening is done in three passes at different radii of the filter, and this parameter is a weight determining the influence of the second and third pass. I never saw the need to adjust this parameter. But if you ever notice an excessive "ringing (moiree)" effect around the edges, you should try to change this setting.

     

    Regards

    Léonie

  • DougS79 Calculating status...

    Wow, that is some very useful information! Glad I stumbled upon this thread.

     

    Greg, what is it about PSE that's a disaster on the Mac? I'm considering downloading the trial, but haven't gotten around to it yet. Also, are you referring to version 9, or the actual "latest" version of 10 which was just released in the last week or so?

     

    Thanks,

     

    Doug

  • DougS79 Level 1 Level 1 (50 points)

    Ok, thanks for the info! I will check out your thread on the Adobe site.

     

    Doug

Actions

More Like This

  • Retrieving data ...

Bookmarked By (0)

Legend

  • This solved my question - 10 points
  • This helped me - 5 points
This site contains user submitted content, comments and opinions and is for informational purposes only. Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use.