Skip navigation

connect imac to tv

616 Views 7 Replies Latest reply: May 8, 2012 7:12 PM by X423424X RSS
Art Starr Level 1 Level 1 (15 points)
Currently Being Moderated
May 8, 2012 4:55 PM

I have a mid-2011 21 inch iMac running OSX 10.7.3. I'm trying to connect it to a Panasonic TV, model TCL47E5. I'm using a brand new Mini Display Port to HDMI cable via the iMac's Thunderbolt port. The input on the TV gives me a message "No signal. Ensure that the external device is turned on and properly connected to the TV's input." The Thunderbolt port in the hardware section of 'About This Mac' shows no activity. I've tried powering up the TV with the computer on, and powering up the computer with the TV on. Can somebody please tell me what I'm doing wrong?

iMac, Mac OS X (10.7.3)
  • captfred Level 7 Level 7 (26,225 points)
    Currently Being Moderated
    May 8, 2012 5:00 PM (in response to Art Starr)

    Look in System Preferences > Displays.  If an Arrangement tab is present then the Mac recognizes an external monitor and it's a TV problem.

     

    If the tab is not present then the Mac doesn't know the monitor is there and is probably a cable problem.

  • captfred Level 7 Level 7 (26,225 points)
    Currently Being Moderated
    May 8, 2012 5:39 PM (in response to Art Starr)

    It could be but I would suspect a connection/cable issue.  Try a different HDMI port, unplug and replug the adapter and the HDMI cable.

     

    You could try a SMC and Pram reset.

     

    SMC

    http://support.apple.com/kb/HT3964

     

    Pram

     

    http://support.apple.com/kb/ht1379

  • X423424X Level 6 Level 6 (14,190 points)
    Currently Being Moderated
    May 8, 2012 6:07 PM (in response to Art Starr)

    Set the TV to the input you connected the HDMI cable to.

     

    On your computer, if you open the Displays preferences and do not see an Arrangement tab (or there is an Arrangement tab that shows only a single monitor) then there is something physically wrong with your connection.  Try clicking Detect Displays just to see if the computer can now sense the presence of the connection.  Check your cables and make sure the mini-displayport plug is pushed firmly in so that essentially all the metal part disappears inside the socket.  Mini-displayport plugs can be a little tricky in that you need to make sure the plug is fully seated in their socket.

     

    If you do have an Arrangement tab, and it shows two screens, then click Gather Windows to bring the TV's Displays preferences on to your main screen if the TV is not yet showing an image.  Set the proper resolution (probably 720p, 1080i, or 1080p).  Set the refresh rate (probably 60Hz) if that preference is shown.  You should see a picture at this point.  I  recommend turning off mirrored displays if it is enabled (more about this below).

     

    You may have to play with the underscan/overscan settings on your TV and the displays prefs for the TV if the picture is too small or larger for the TV screen.

     

    Also, you need to set your Sound preferences to output to the HDMI connection.

     

    When using Lion, do not run in Lion full screen mode.

  • Eric Fauque Level 3 Level 3 (985 points)
    Currently Being Moderated
    May 8, 2012 7:05 PM (in response to Art Starr)

    I would suggest that you get a mini display port to hdmi adapter and a hdmi cable instead of a all in one mini display to hdmi cable. That way you can test the hdmi cable with an other device like a xbox or a blue ray player.

    I got my mini display to hdmi adapter at monoprice for about 5$ and an other 5$ for a hdmi cable and it works perfectly with my panasonic hdtv.

  • X423424X Level 6 Level 6 (14,190 points)
    Currently Being Moderated
    May 8, 2012 7:12 PM (in response to Art Starr)

    The only time I've ever run a cable as an "adapter" was for firewire400 to firewire800.  In all other cases I've only used adapters.  There's plenty of mini-displayport to HDMI adapters to choose from.  I always recommened monoprice.com for stuff like this (cables and adapters):

     

    Mini DisplayPort | Thunderbolt® to HDMI® Adapter w/ Audio Support

     

    As for lion full screen mode, I don't use lion, but I believe that is where an application takes over the entire main screen.  The menu and dock are not shown unless you mouse over the area.  And there is a pair of double arrows in the upper right of the menu bar to enter/exit full screen mode (reference).  I believe if you have that enabled additional monitors are blanked out which is why I say don't use it when you want to use additional monitors.

Actions

More Like This

  • Retrieving data ...

Bookmarked By (0)

Legend

  • This solved my question - 10 points
  • This helped me - 5 points
This site contains user submitted content, comments and opinions and is for informational purposes only. Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use.