Currently Being ModeratedSep 12, 2012 2:49 AM (in response to Bousque)
I might have added, that whether coincidence or not, I had just connected the PB to an ethernet router when the problem started happening. I don't recall whether or not I had turned everything off before attaching the cable.
Currently Being ModeratedSep 13, 2012 2:31 PM (in response to Bousque)
Is the grey screen with some typing possible relevant or interesting in any way?
When you say some typing possible, I think it might be loading up the open firmware.
This is normally a screen with writing that allows you to type a command.
If you can type, then try typing mac-boot.
Do you have anything attached to your PowerBook, Via USB or Ethernet cable during boot up?
If so unplug everything and try restarting it.
Have there been any upgrades to this PowerBook, like memory? or a chnage in target disk?
Have you tried resetting the PRAM/NVRAM by doing the following:
- Shut down your Mac.
- Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
- Turn on the computer.
- Press and hold the Command-Option-P-R keys before the gray screen appears.
- Hold the keys down until the computer restarts and you hear the startup sound for the second time.
- Release the keys.
Currently Being ModeratedSep 13, 2012 2:54 PM (in response to Knucklesmac)
Thanks for this... yes I had reset the PRAM as part of the set of things done initially. Just did it again, the machine still stops at the bitten Mac with no spinning wheel - I will leave it for ages though to see what happens.
When it was still getting to the blank screen I did try typing various things, don't remember what, it did occur to me that it was putting itself into some kind of firmware or whatever it is, state.
Nothing is attached at all (except when in TDM). As it was second hand I don't know if it had any memory upgrades, how would I know (bearing in mind I can't turn it on to find out!). Not sure re change in target disk beyond what I have done in TDM, there was only one OS on the machine, there's now two, the reinstalled one and the old one.
Currently Being ModeratedSep 13, 2012 3:06 PM (in response to Bousque)
Have your tried holding down the option key when booting. This should bring up a drive selection and allow you to select the hard drive.
When you say there is now two OS's on this PowerBook, has there been two installs of two different versions of the OS?
Currently Being ModeratedSep 13, 2012 3:30 PM (in response to Knucklesmac)
Yes tried that before and now again. Same result, bitten symbol, stuck.
There are two copies of OS because the last-ish resort was to try reinstalling and so that had to be the version that came with the machine, that installed successfully but restarting was little better, but the old version will be archived or whatever, automatically I'd have thought...?
Currently Being ModeratedSep 13, 2012 3:41 PM (in response to Bousque)
It's possible to have two Mac OS X's installed on one drive.
Have you tried this:
Restart whilst holding down Command-S
The screen should turn black and load some text
At the prompt type
fsck -fy and press Return
Hopefully some repairs will be performed.
At the prompt type
reboot and press Return
If that doesn't provide any help then try starting in safe mode.
Once in safe mode, you can set the startup disk and reboot.
If that don't help, then all I can suggest is a clean install of the OS.
Using a Mac OS X install disk either retail or for a PowerBook G4, boot and upon selecting the destination drive, select option, then erase and reinstall.
A fresh install should resolve this problem as a last resort.
Best of luck, let us know how you get on.
Currently Being ModeratedSep 13, 2012 3:51 PM (in response to Knucklesmac)
I don't remember starting with Cmd S and haven't seen the letters fsck -fy before, well again it didn't get beyond the bitten symbol. I think you are right that the last resort will be to erase-reinstall (but not at this time of night!) and see what that does, any data left on here now is probably going to be abandoned anyway.
Currently Being ModeratedOct 28, 2012 4:06 AM (in response to Bousque)
Well I thought it was time to try again, having established that everything of relevance has been taken off the machine, I did a total erase-install. And it started up first time after all the installation was done, and then started going wobbly again, and on restart did exactly what it was doing before. Ho hum.
Currently Being ModeratedOct 28, 2012 10:18 AM (in response to Bousque)
More Like This
- Retrieving data ...
- This solved my question - 10 points
- This helped me - 5 points