Skip navigation

How to quiet a noisy mac pro?

3064 Views 11 Replies Latest reply: Nov 22, 2012 2:18 PM by Rob Wilson RSS Branched to a new discussion.
Vlad Cohen1 Level 1 Level 1 (5 points)
Currently Being Moderated
Dec 17, 2011 10:12 AM

I have a mac pro from 2008, a dual quad core 3.0 Intel Xeon model, which I have upgraded to 12 GB of RAM and to an ATI Radeon HD 4870 Graphics card.

 

From the very outset, even before those upgrades, this machine has always been very noisy. It's like working next to a car engine. I took it for granted when it was new that this was simply a tradeoff for what seemed like a lot of processing power at the time. However, the more I hear other people talking about their mac pros, the more I hear people saying their machines run nearly silently.

 

Is there anything I can do to make my machine quieter? I do a lot of video work on it and I have to use headphones to hear the video over the sound of the computer. I am very tempted to downgrade to an Imac hoping that it will reduce the noise.

 

I have tried to reset the SMC by unplugging the cables from the machine and restarting it, and I have cleaned the inside of the machine as thoroughly as I can without any specialist equipment.

 

Any advice would be great. Maybe my machine is just a lemon, but if I can improve it I would like to try.

 

Many thanks in advance

Mac Pro, Mac OS X (10.7.2), 2 x 3 GHz Quad Core Intel Xeon
  • Linc Davis Level 10 Level 10 (107,575 points)
    Currently Being Moderated
    Dec 17, 2011 10:46 AM (in response to Vlad Cohen1)

    The moving parts are the fans and the hard drive(s). Determine the baseline noise level by booting in safe mode and not logging in. If the fans seems noisy then, they may be running too fast because of conditions such as a faulty temperature sensor, poor ventilation, or dust buildup -- or the bearings of one may be failing.

     

    Noisy hard drives can be replaced, if necessary.

     

    Noise could also be caused by transmitted vibration in loose parts such as drive sleds.

  • shanks101 Level 1 Level 1 (0 points)
    Currently Being Moderated
    Dec 17, 2011 8:29 PM (in response to Vlad Cohen1)

    vladcohen- gurantee you yours is not a lemon...i use my mac pro for editing as well and mines like that... its annoying but i learnt to live with it.......

  • SiliconSam Calculating status...
    Currently Being Moderated
    Dec 17, 2011 8:47 PM (in response to Vlad Cohen1)

      Use a program like smcFanControl to see what RPM's the fans are turning at.  If they are spinning at normal speed, could be your 4870 fan, or one of the hard drives is going south.

     

      I have a 2006 Mac Pro and all 4 fans are turning between 599 and 1062 RPMs.  CPU 963 RPms, Exhaust 1062, I/O 963, and Power Supply 599.  When I use Handbrake, I adjust some of the fans closer to 1500 RPMs to compensate for 8 cores running at full capacity.  Mine is nearly silent right now as well.

  • The hatter Level 9 Level 9 (58,535 points)
    Currently Being Moderated
    Dec 18, 2011 5:47 AM (in response to Vlad Cohen1)

    Remove

     

    graphic card and make sure it is clean and firmly reset. It probably has a latch on the side of the slot lane.

     

    disk drives - tight but not too, and some users put in noise dampening washers

     

    memory riser cards (2) and the DIMMs though you had to do that when you added RAM and Risers and DIMMs do require a rather firm push to click into place.

     

    loose fan housing is also possible.

     

    not really a lemon. but maybe a part is loose or a screw missing (lteral and figurative)

     

    as long as it passes the Apple Hardware Test and is stable etc and doesn't kick up gpu or memory errors.

     

    Mine was quiet until I added an older 10K Raptor 74GB that seemed to not be that noisy but caused the case to "humm" and the vibration of it and other parts "clash" or setup some discord.

     

    The way mine got quiet again, was to use some washers and insulation padding where metal on metal was an issue, then, to put it on its side. Quiet again. But there could be a high pitched humming whine that was almost impossible to hear, but very irritating. One of those things hard to detect but could hear even as I walked into my office.

  • shanks101 Level 1 Level 1 (0 points)
    Currently Being Moderated
    Dec 19, 2011 12:27 AM (in response to The hatter)

    The hatter is right!! mine was making all kinds of noise like i was in a aeroplane about to take off.. i brought it to the shop it was the carriage which wasnt placed properly and hitting the metal.. placed it tightly and very quiet now..

     

    should get it checked out internally.. might be worth a look

  • ecorb Level 1 Level 1 (0 points)
    Currently Being Moderated
    May 22, 2012 4:47 PM (in response to Vlad Cohen1)

    THIS FIXED MY NEARLY IDENTICAL COMPUTER AND SYMPTOMS:

     

    I've been trying to correct the full-speed fan syndrome on my mac pro (2008 2.8 quad core) for months now. I finally downloaded and installed iStat, then saw that the "Northbridge" temperature was way higher than any other temp (it typically ramps up from 140 to 259F).

     

    What fixed it finally was simply disconnecting and reconnecting the northbridge heatsink-to-motherboard connecter (simple two-prong connecter just left of center in this photo:  http://forums.macrumors.com/showthread.php?t=544597&page=2).

     

    Perhaps a weak connection there led to erroneous resistances and a false temperature reading.

     

    The connecter is accessible by just taking the side panel of the computer off and removing the video "card".

     

    The Northbridge temperature is now stable around 122F, more in line with the other temps.

     

    It's kind of embarassing what I went through in the way of troubleshooting, but let's just say I wish I'd started with iStat six months ago.

  • The hatter Level 9 Level 9 (58,535 points)
    Currently Being Moderated
    May 22, 2012 5:01 PM (in response to ecorb)

    Good shot. I recommend off the bat that people install SmcFancontrol 2.3 and Hardware Monitor and if necessary set HM to alert if any sensor reading exceeds a threshold (but you have to set each manually).

     

    Did you ever touch or go in that area in the past? or was it just a freak event? and got loose by itself.

  • mckayk777 Level 1 Level 1 (25 points)
    Currently Being Moderated
    May 22, 2012 8:03 PM (in response to Vlad Cohen1)

    Hello all of my fellow noisy fan suffers,

     

    After trying many things calling apple support, also the people that sold us the computer, reading many posts about resetting this or installing that I sort of gave up.

     

    Then one morning when the temperature in town was near on 0 celcius and the computer had just been turned on, and the fans where hailing away at full throttle, I put the computer to sleep.... ahhh no more noise. but alas I had work to do so had to wake it back up again.

     

    Funny thing is when I woke it up the fans where not going at full throttle anymore, infact they where as quite as a mouse. This I found interesting and a huge relief.

     

    This has not stopped the problem, most mornings no matter how cold it is fans still play up but a quick shhh my dear machine go to sleep for a minute then start it back up and no more noise.

     

    I am still waiting for the solution (maybe buying a PC "HOPE NOT") Hope more that apple will get off their collective backsides and fix the problem.

     

    But for all of us out there that is having this ear ache of a problem maybe my solution could help just a little.

     

    All the best

    Kevin

     

    P.S. This is the same message I gave to another post but would like to add that you should check dust build up between the fan and and what they are there to cool.

  • ecorb Level 1 Level 1 (0 points)
    Currently Being Moderated
    May 22, 2012 9:09 PM (in response to The hatter)

    "Good shot. I recommend off the bat that people install SmcFancontrol 2.3 and Hardware Monitor and if necessary set HM to alert if any sensor reading exceeds a threshold (but you have to set each manually).

     

    Did you ever touch or go in that area in the past? or was it just a freak event? and got loose by itself."

     

     

     

    I don't think I've ever bumped that connecter. I suspect some form of nearly invisible, possibly bi-metallic corrosion occurs with electrical connecters sometimes and the simple act of unplugging and plugging it back together reconnects the contacts as per the design.

     

    I actually bent one of the prongs on the motherboard very slightly to creat a bit of side force in an attempt to prevent another occurrance.

  • Rob Wilson Level 1 Level 1 (0 points)
    Currently Being Moderated
    Nov 22, 2012 2:18 PM (in response to Vlad Cohen1)

    Same here.  The noise is a surging sound, which used to rise when certain apps were accesed.  Now it is fairly steady.  I am guessing this is a faulty hard drive..... Thanks for the suggestions.  I will take it in and report back.

Actions

More Like This

  • Retrieving data ...

Bookmarked By (2)

Legend

  • This solved my question - 10 points
  • This helped me - 5 points
This site contains user submitted content, comments and opinions and is for informational purposes only. Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use.