Dannerino

Q: Bad OS Disk 2

I have a G5 Power PC with a burnt hard drive.  I installed another hard drive (that worked fine the last time I used it).  I used the original grey OS X Tiger 10.4.2 disks, but disk 2 has some scratches and the installation process stopped.

 

I've attempted to clean the disk with no luck. I've installed a downloaded version of Tiger onto a 16G thumb, and used Disk Utility to make it bootable.  However, holding the option key upon bootup does not bring up a boot options menu.  In fact, most keys you hold down for different boot options do not work.  The only that seemed to work was CMD V for verbose mode.

 

When I attempt to boot, either holding or not holding down keys for boot options, I get one of two results.  It either returns to the installation process and asks for disk 2, or it presents me with a screen showing two buttons (a round arrow which I assume means Go Back and a right pointing arrow which must be Next) and an icon of a disk with an X on it.

 

Questions: Do I have a G5 model that does not allow booting from a thumb drive?  Why doesn't it present a boot options menu when I hold the option key?  What options do I have to get Tiger installed on this machine?

iMac, Mac OS X (10.4.2)

Posted on May 16, 2013 2:10 AM

Close

Q: Bad OS Disk 2

  • All replies
  • Helpful answers

  • by Roger Wilmut1,

    Roger Wilmut1 Roger Wilmut1 May 16, 2013 2:39 AM in response to Dannerino
    Level 9 (78,303 points)
    iTunes
    May 16, 2013 2:39 AM in response to Dannerino

    Your best bet is to ring the online store at the number given at bottom left of this page and see if you can still get the insall disks for your Mac - give them the serial number. If it's still available the cost is nominal.

  • by rccharles,

    rccharles rccharles May 20, 2013 11:11 AM in response to Dannerino
    Level 6 (8,506 points)
    Classic Mac OS
    May 20, 2013 11:11 AM in response to Dannerino

    Apple has not released a downloadable copy of tiger.  You have an illegal copy. May contain malware.

     

    Only a few models of the G5 boot from USB.

     

    There may be a lifetime warrenty on the media.  Check with apple.

     

    Restore Tiger 10.4 & Leopard 10.5  DVDs are available from Apple by calling 800-767-2775 as of January 20, 2013. Have your serial number ready. Have your credit card ready too.  There is a small fee.

    https://discussions.apple.com/thread/4720126?tstart=0

     

    Robert

  • by Dannerino,

    Dannerino Dannerino May 23, 2013 12:34 AM in response to rccharles
    Level 1 (0 points)
    May 23, 2013 12:34 AM in response to rccharles

    I will go with the restore DVD option. 

     

    In the meantime, it seems the iMac only boots to the continuation of the previous install.  Is this by design?  And if so, what do I do when I have the Tiger restore disk in hand?  Or, more importantly (to me anyway as someone always looking to learn more), is there a method to bypass/cancel/skip the previous install when I fire it up?

  • by rccharles,

    rccharles rccharles May 23, 2013 11:32 AM in response to Dannerino
    Level 6 (8,506 points)
    Classic Mac OS
    May 23, 2013 11:32 AM in response to Dannerino

    However, holding the option key upon bootup does not bring up a boot options menu.  In fact, most keys you hold down for different boot options do not work.

     

    or it presents me with a screen showing two buttons (a round arrow which I assume means Go Back and a right pointing arrow which must be Next) and an icon of a disk with an X on it.

     

    This is the startup menu which you are calling "boot options menu" I assume.

     

    I assume means which is refresh boot menu

     

    right pointing arrow which is to initiate boot.

     

    The startup manager will list all of your bootable partitions then give you a choice of which to boot.

     

    Try holding down the option key then power on. This brings up the startup manager. Click on your hd. Click on right arrow key.

     

    I should have commented on the above earlier.

     

    Let's get the exact machine you have. 

    Query by serial number

    Apple's warrenty database will identify the type of Mac you have.  Your serial number is securely sent, but you get only the name of your machine.

    https://selfsolve.apple.com/agreementWarrantyDynamic.do

     

    This site provides more information, but lacks security.

    "A serial number is a unique, identifying number or group of numbers and letters assigned to an individual piece of hardware or software. It's used for various things depending on the product / brand but what is your Mac's serial number for and more importantly... what is it hiding and what can it do for you ?"

    http://www.appleserialnumberinfo.com/Desktop/index.php

     

    learn more), is there a method to bypass/cancel/skip the previous install when I fire it up?

     

    Sure. Place dvd in drive.  I like to get startup menu.

    The startup manager will list all of your bootable partitions then give you a choice of which to boot.

     

    Try holding down the option key then power on. This brings up the startup manager. Click on your hd. Click on right arrow key.

     

    Robert

  • by Dannerino,

    Dannerino Dannerino May 23, 2013 3:05 PM in response to rccharles
    Level 1 (0 points)
    May 23, 2013 3:05 PM in response to rccharles

    Thanks Robert.  I ran my serial number through both links you provided.  No warranty remaining. 

     

    I'll try the option key before power button when I can later this evening.  I appreciate the help.

  • by rccharles,

    rccharles rccharles May 23, 2013 5:01 PM in response to Dannerino
    Level 6 (8,506 points)
    Classic Mac OS
    May 23, 2013 5:01 PM in response to Dannerino

    I was interested on information about your machine.

    When I went to the site I got information like this:

    Picture 2.png

     

    copy & paste

     

    --------------------------------------------------------------

     

    -------------------------------

    How to show us a screen image.  Avoid personal identification.

     

    command + shift + 3   Will take entire screen.  You hear a click.

    command + shift + 4 Lets you decide what to take.  Mouse pointer changes. Move mouse to upper left corner of desire image.  Hold down left mouse key where to start image.  Drag mouse to lower left of where you want to stop image.  Release mouse.

     

    You will get a picture n.png file on the desktop.

     

    one the forum input panel you will see the camera icon.

     

          Picture 18.png

     

    click on camera icon.

     

    another window will appear.

     

    Make sure you have selected the from your computer tab.

     

    click on Browse button

     

    An open file panel appears.  Select the file.

     

    After selection a file, I have this screen showing.

    Picture 5.png

     

     

    You will have to click on Insert Image.  You may have to scroll down to see Insert Image button.

  • by Dannerino,

    Dannerino Dannerino May 23, 2013 8:31 PM in response to rccharles
    Level 1 (0 points)
    May 23, 2013 8:31 PM in response to rccharles

    Mac Info.jpg

    Thanks for the detailed instructions Robert.  I'm a programmer so am fairly familiar with screen capture, insert image, etc.  I mention this as a time saver for you, as you don't need that thorough a description (not that I don't appreciate it).

     

    At any rate, here's my info from the 2nd link you provided earlier.

     

    Dan

  • by Dannerino,

    Dannerino Dannerino May 25, 2013 8:14 AM in response to rccharles
    Level 1 (0 points)
    May 25, 2013 8:14 AM in response to rccharles

    I tried a few things and here's what happened:

     

    Holding down option, then pressing power

         The boot menu appeared, the HD had an X on it (no surprise)

         Clicked the back button, nothing happened

         Clicked the forward button, got the apple logo screen and it froze there

     

    Held down shift, then power

         White blank screen

     

    Held option, then power, then inserted OS disk 1

         Disk ejected at boot menu

         Reinserted, ejected again

         Clicked back and reinserted, boot menu appeared

         HD and CD Rom had Xs

         Hardware test was available, everything passed

     

    Restarted, option key down

         Boot menu, HD with X

         Hit back and inserted CD again

         Ejected this time, boot menu with X

     

     

    ----------------

     

    I'd like to restart the installation, just to see something different.  Or, any other ideas for my next step?

  • by Dannerino,

    Dannerino Dannerino May 25, 2013 8:21 AM in response to Dannerino
    Level 1 (0 points)
    May 25, 2013 8:21 AM in response to Dannerino

    Duh, perhaps if I held the option key on restart after doing the hardware test, and insert the disk, it would show.  Yep, it did.  And perhaps, once it appears, X or no X on it, if I press the forward button...

     

    It brought me to the installer.  I ran in here to post, am going to try to choose minimal install options (if I even have those choices) and see if I can avoid the need for disk 2.  It's a hair brained idea, but it's something, for now.

  • by BDAqua,

    BDAqua BDAqua May 27, 2013 1:32 PM in response to Dannerino
    Level 10 (123,765 points)
    May 27, 2013 1:32 PM in response to Dannerino

    That second Disc thing happens frequently, the best way around it is to do a Custom install, and eliminate enough Printer Drivers, Languages, Fonts, and Applications you don't need... then it may skip #2 altogether.

     

    http://support.apple.com/kb/HT1442