Skip navigation

PowerMac G5 Dual 2.0GHz June 2004 seems dead... how do I fix it?

731 Views 11 Replies Latest reply: Jul 30, 2013 7:08 AM by mikiotty RSS
mikiotty Level 1 Level 1 (0 points)
Currently Being Moderated
Jul 3, 2013 7:50 AM

Hello everyone!

I recently bought a second-hand PowerMac G5 Dual 2.0GHz June 2004 model. The guy that sold it to me said he was selling it because of a power supply issue. He told me that an Apple Genius noticed a PSU failure and that a PSU replacement would cost him about 350€ (I'm in Italy), so he decided to sell the computer. Meanwhile he bought a replacement PSU from an eBay shop. When I first plugged in the Mac (with the original PSU), there were no life signs. I thought that was a real PSU problem and I decided to test the new PSU before putting it into the computer. I connected the PSU to the power and... it literally exploded. Lucky I didn't put that PSU into my G5.

Anyway, I'm in the same situation as before. When I first tried to plug in the computer, I noticed a very short blink from the power LED. However, the computer won't start at all. No fan noise, no lights, nothing. I then tried to reseat RAM, video card, fans... nothing. I then tried to replace the PRAM battery and resetting the PMU, same results. I decided to reseat the processors being extremely carefully, but nothing. At this point, I decided to test the original PSU on the bench and it seems to be outputting all the correct values (all the 5V, 3.3V, 12V, -12V, 25V) on the correct pins, even under a small charge. I then tried connecting pins 14-23 and the PSU fan started running. I then tried to manually give the OK for the voltage to come up on the logic board by connecting those pins with the PSU plugged into the logic board. All the fans started running very slowly, but that's it. Nothing else happened (Note: I tried this without RAM, CPUs, video card etc. I then read that this model won't start without even one CPU, they both have to be on the logic board, that's probably because it didn't proceed with the boot sequence).

Any idea? I don't want to spend 950€ on a new logic board, and I may try to repair the components on the logic board myself if it's necessary (I have a lot of experience in soldering etc, I already replaced 6 caps on an iMac G5 logic board and now it works perfectly). Anyway, reading on the web, I think I have a bad switch on the front board (the one with the power button). The button itself works, maybe the circuitry on the board died. I'm not going to buy any component before I'll find out what the exact problem is BTW.

 

I rely on your help! Thank you (sorry for my english)!

PowerMac
  • BDAqua Level 10 Level 10 (114,715 points)

    I think it does need at least one CPU, CPU0, it may start without CPU1.

     

    PS. Your English needs no apology, quite good in fact!

  • BDAqua Level 10 Level 10 (114,715 points)

    It certainly could be that little board behind the power button.

     

    Here's some more info on G5 PSU voltage values:

     

    http://www.insanelymac.com/forum/lofiversion/index.php/t105113.html

  • BDAqua Level 10 Level 10 (114,715 points)

    On the iMac G4 I'd say it's a bad capacitor that needs to bleed down. On the G5, try adding one component at a time between the minimal way it started & up, I suspect maybe Video card, but...

  • BDAqua Level 10 Level 10 (114,715 points)

    On the G5 anyway, the little board behind the power button may do this.

Actions

More Like This

  • Retrieving data ...

Bookmarked By (1)

Legend

  • This solved my question - 10 points
  • This helped me - 5 points
This site contains user submitted content, comments and opinions and is for informational purposes only. Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use.