AlanBPimentel
Level 1 (8 points)
Mac OS X

Q: Issues to update to OS X El Capitan from OS X Snow Leopard

Hi there,

I have an issue to update to OS X El Capitan from Snow Leopard (10.6.8)

 

Well, I tried some procedures to fix it and saw many answers here but not helped me yet.

The message is basically: OS X can not be installed on your computer. File system verify or repair failed, restart and try again.

 

What I've done:

- Reseted NVRAM

- Reseted SMC

- Safe Mode (doesn't worked, and appears a black screen with white text with some information about kernel. There I saw this information: The OS X isn't set yet.

- Recovery Mode (not applicable, I'm without CD)

 

There is some way to fix it without OS X CD?

Could someone suggest some other procedure?

MacBook Pro

Posted on Jul 25, 2016 5:53 PM

Close
AlanBPimentel

Q: Issues to update to OS X El Capitan from OS X Snow Leopard

  • All replies
  • Helpful answers

  • by Carolyn Samit,

    Carolyn Samit Carolyn Samit Jul 25, 2016 6:09 PM in response to AlanBPimentel
    Level 10 (120,791 points)
    Apple Music
    Jul 25, 2016 6:09 PM in response to AlanBPimentel

    See if your Mac meets El Capitan requirements >  Upgrade to OS X El Capitan - Apple Support

  • by AlanBPimentel,

    AlanBPimentel AlanBPimentel Jul 25, 2016 6:10 PM in response to Carolyn Samit
    Level 1 (8 points)
    Mac OS X
    Jul 25, 2016 6:10 PM in response to Carolyn Samit

    Yes! MacBook Pro 2010

  • by Carolyn Samit,

    Carolyn Samit Carolyn Samit Jul 25, 2016 6:14 PM in response to AlanBPimentel
    Level 10 (120,791 points)
    Apple Music
    Jul 25, 2016 6:14 PM in response to AlanBPimentel

    Without the install disc that came with your Mac the only way to repair the startup disk is to take your Mac to an Apple Store. They can repair the disk and upgrade your Mac to El Capitan.

     

    http://www.apple.com/retail/geniusbar/

  • by AlanBPimentel,

    AlanBPimentel AlanBPimentel Jul 25, 2016 6:23 PM in response to Carolyn Samit
    Level 1 (8 points)
    Mac OS X
    Jul 25, 2016 6:23 PM in response to Carolyn Samit

    Hum, ok! But think you that if I catch the install disc and start the MacBook pressing C key, the system will show the recovery mode?

  • by steve626,

    steve626 steve626 Jul 25, 2016 8:16 PM in response to AlanBPimentel
    Level 4 (1,551 points)
    Jul 25, 2016 8:16 PM in response to AlanBPimentel

    You need to use the correct install disk to fix your file system from it. However, in the absence of the correct install disk, there are two things you can try:

     

    (1) Do a Safe Boot. Hold the Shift key when starting up. If done properly, the boot up will take a longer time and the screen will look different than usual, and it may show a different progress bar. It might take 5 or more minutes. Don't interrupt it. After it is done booting, then restart normally and try your El Capitan update again.

     

    (2) Boot into single user mode and use the fsck -fy command. Details are at

     

    Resolve startup issues and perform disk maintenance with Disk Utility and fsck - Apple Support

     

    but here is the basic process from the Apple Support page referenced above:

     

    (1) Start up your computer in single-user mode to reach the command line. This means, hold Command-S when starting up your computer. When doing this, a different user interface will appear, looking much like a typewriter bare bones interface, not the usual graphics user interface.

     

     

    (2) Wait a minute until the lines of text stop scrolling. Wait an additional 30 seconds. At the command-line prompt type:

     

    /sbin/fsck -fy

     

    Press Return. fsck will go through five "phases" and then return information about your disk's use. Once it finishes, it'll display this message if no issue is found:

     

    ** The volume (name_of_volume) appears to be OK

     

    If fsck finds issues and alters, repairs, or fixes anything, it displays this message:

     

    ***** FILE SYSTEM WAS MODIFIED *****

     

    If this message appears, repeat the fsck command you typed in step 2 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).

     

    When fsck reports that your volume is OK, type

     

    reboot

     

    at the prompt and then press Return.

    Your computer should now start up normally and allow you to log in.

     

    At this point, retry your El Capitan update.