Where can I find Huawei E270 wireless modem driver for OS X???

I use the huawei usb hsdpa modem with my mac and the driver was bundled on a CD when I purchased the modem.

I can email you the driver but I have the Huawei E220 not the E270.

Like Tim, I have the 220 but checking the driver list, it appears to be a generic driver. There is a link to my local service (I use the term loosely) provider. I had to force the issue a bit as there was initially no Mac support.

The information/link is about halfway down on the right of the page.

Hi Tim,

Could you please email me the driver of the E220? my email address is sultan.faris@gmail.com

Thank you for your help.

I have put the drivers in a zipped file on my dot mac space so you can download it from the following link


http://homepage.mac.com/timhaigh/E220_Drivers.zip it is 100k download.

Tim

Hi Tim and others

Thanks a lot for your SW. I have still problems with APN configuration.
I'd like to give the modem a new APN for a different provider but every time it tells me "configuration failed".
Could you help me?

thanks a lot

Marco

Hi,
i just got my HuaWei E270 WireLess Modem from StarHub MaxMobile, and will like to install with my MacBook Pro. Have any one had sucessfully install the E270 with MacBook OS X 10.5.x. Pl advice where to download the driver & how to install it.
Thanks & Regards

Hi, I'm on StarHub MaxMobile too and I'm currently using the E220 drivers from http://portal.myglobe.com.ph/portal/Suboverview.do?aid=44364&id=1724 for my E270.

It works just fine on Leopard and Tiger and I have not encountered any known problems so far.

The detailed installation guide can be found here: http://www.myglobe.com.ph/myGlobe/pdf/HuaweiInstallation_&_Configuration_for_Macv2.pdf

Hope it helps.

sorry for the double post

Message was edited by: numzkull

After calling Starhub, this is the solution.

1. Install the driver from the CD provided, before connecting the USB modem.
2. Edit network preference in *"System Preference"* > "Network"
2.1 You should see the HUAWEI Mobile at the left sidebar. Click on it and edit setting as follow:
Location: Automatic
Configuration: Default
Telephone Number: *99#
Account Name: +(Live it blank)+
Password: +(Live it blank)+
<Enable> Show modem status in menu bar
2.2 Edit the "Advanced..." button as follow:
Modem
Vendor: Other
Model: *HUAWEI Mobile Connect - 3G Modem, /System/Library/Modem Scripts/HUAWEI Mobile Connect - 3G*
<Enable> Enable error correction and compression in modem
Dial Mode: *Wait for dial tone before dialing*
Dialing: Tone
Sound: Off
PPP
Setting: Session
+Check the following only:+
<Enable>Disconnect when user logs out
<Enable>Redial if busy
Redial 1 times
Wait 5 seconds before redialing
+Click Apply and exit system preference+
3. Connect the USB modem until the blue light is blinking.
4. Edit the configuration as follow:
4.1 Open "Aplication" > "MobileConnect"
4.1.1 Under the *"Dial up"* tab, click on the Setting button.
4.1.2 Create a new profile as follow:
Profile Name: "Starhub_Mobile" (Can be any name)
Access Point Name: "shwap"
Telephone Number: *99#
Account Name: (Live it blank)
Password: (Live it blank)
Authentication: CHAP
+Click "Save", and use this profile.+
4.2 Click on the connect button and the connection should start.

Tips: Once the Modem is shown on the menu bar, you can click on "Connect HUAWEI Mobile" to connection in future.

Message was edited by: Kah Chun

HUAWEI drivers are pretty generic so therefore the howto I wrote in this thread may help.

HUAWEI drivers are pretty generic so therefore the howto I wrote in this thread may help.