Currently Being ModeratedNov 5, 2012 3:13 AM (in response to ariesgirlinoz)
Try Forget This Network.
Settings>Wi-Fi>tap little arrow on right of network.
Currently Being ModeratedNov 5, 2012 4:07 AM (in response to Diavonex)
I don't think I have that option. when I press the little blue button to the right of my network, I have a choice of DHCP, BootP and Static under a heading of IP Address, a Renew Lease button and a choice of Off, Manual and Auto under a heading of HTTP Proxy - they are currently set to DHCP and Auto.
Currently Being ModeratedNov 5, 2012 4:35 AM (in response to Diavonex)
Apologies hadn't realised that was a screen shot, but no definitely don't have the Forget this network option.
To JimHdk - it has a couple of numbers N150 and WNR1000 and we only got it a month or so ago - it has worked perfectly for wifi connections with the MacBooks and my Mac desktop
Currently Being ModeratedNov 5, 2012 4:52 AM (in response to Diavonex)
No, that was part of my question. I've seen some sites talking about problems with iPads and iPhones following the upgrade to iOS6 and suggesting that you needed to downgrade the router firmware. I've never interfered with my router apart from setting it up, so I was a bit nervous about changing things.
It's almost midnight here, so I'm going offline now. Will check bak in the morning - thanks very much for your assistance.
Currently Being ModeratedNov 5, 2012 5:02 AM (in response to ariesgirlinoz)
If you have never updated the firmware in your router you likely have the initial release version.
Note that there are three versions of the Netgear WNR1000 router v1, v2, and v3. You will have to check to see which one you have.
To get Netgear firmware go here: http://downloadcenter.netgear.com/en/default.aspx
Currently Being ModeratedNov 5, 2012 5:30 AM (in response to ariesgirlinoz)
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
Apple's iOS 6 Wi-Fi problems
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
iPad Wi-Fi Problems: Comprehensive List of Fixes
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Currently Being ModeratedNov 6, 2012 12:12 AM (in response to JimHdk)
I have v3. When I go to the download centre, it says the four firmware options are all for North America only - I'm in Australia - should I still try downloading?
Maybe I should try calling Netgear. The fact that it connected automatically in the Apple shop suggests it is likely to be a router issue.
@Texas Mac Man - it's not that I can't get a connection, it's that it won't automatically connect and I have to manually connect each time, including entering the password. No problems once I do that.