Error type 127

I have a G4 that has both OS 9 and OS X. I'd only been using OS 9, then when I started using OS X more I tried starting up in 9 again and it starts up in 9.2.2 then gives me a system error message with Error Type 127. When I click the restart button, it changes to address error and the restart button on the screen does nothing.

I've tried restarting with extensions off, zapping the PRAM, and starting from the software install disk (both holding down C and holding down Command-Option-Shift-Delete) and it still gives me the error message. The past few times I've tried restarting, I've also noticed that it doesn't make the startup sound anymore, even when it's been off for a while.

Any ideas??

Power G4, Mac OS 9.2.x

Posted on Aug 27, 2006 11:36 AM

Reply
2 replies

Aug 27, 2006 1:01 PM in response to Iserel

Hi Iserel,
Welcome to the Discussions.

Try starting in Safe Mode by holding the shift key as you start and release it when you see the logo and spinning progress indicator. That will run a disk repair utility while starting. If it starts sucessfully, restart normally.

The old error numbers are meaningless for the most part but 127 is at times a file system error. If starting in safe mode doesn't do it you may need another utility such as Disk Warrior.

John

Aug 27, 2006 2:50 PM in response to Iserel

Mac OS System Error Codes: 0 to -261
The following list provides an explanation of system errors 0 to -261. This document applies to Mac OS 9 and earlier.


Notes

1. Items listed in [brackets] are old result code meanings.

2. ???? This information was not available.I/O System Errors -17 controlErr Driver can't respond to Control call
-18 statusErr Driver can't respond to Status call
-19 readErr Driver can't respond to Read call
-20 writErr Driver can't respond to Write call
-21 badUnitErr Driver ref num doesn't match unit table
-22 unitEmptyErr Driver ref num specifies NIL handle in unit table
-23 openErr Requested read/write permission doesn't match driver's open permission, or Attempt to open RAM serial Driver failed
-24 closErr Close failed; Permission to close .MPP driver was denied
-25 dRemovErr tried to remove an open driver
-26 dInstErr DrvrInstall couldn't find driver in resources
-27 abortErr IO call aborted by KillIO; Publisher has written a new edition OR
-27 iIOAbortErr IO abort error (Printing Manager)
-28 notOpenErr Couldn't rd/wr/ctl/sts cause driver not opened
-29 unitTblFullErr Unit table has no more entries
-30 dceExtErr dce extension error

File System Errors -33 dirFulErr Directory full
-34 dskFulErr Disk full
-35 nsvErr No such volume; volume not found
-36 ioErr I/O error (bummers)
-37 bdNamErr Bad file name; there may be no bad names in the final system!
-38 fnOpnErr File not open
-39 eofErr End of file; no additional data in the format
-40 posErr Tried to position to before start of file (r/w)
-41 mFulErr Memory full (open) or file won't fit (load)
-42 tmfoErr too many files open
-43 fnfErr File not found; Folder not found; Edition container not found; Target not found
-44 wPrErr Diskette is write protected; Volume is locked through hardware
-45 fLckdErr File is locked
-45 fLckedErr Publisher writing to an edition
-46 vLckdErr Volume is locked through software
-47 fBsyErr File is busy (delete); Section doing I/O
-48 dupFNErr Duplicate filename (rename); File found instead of folder
-49 opWrErr File already open with with write permission
-50 paramErr Error in user parameter list
-51 rfNumErr Reference number invalid
-52 gfpErr Get file position error
-53 volOffLinErr Volume is off line
-54 permErr Software lock on file; Not a subscriber [permissions error on file open]
-55 volOnLinErr drive volume already on-line at MountVol
-56 nsDrvErr no such drive (tried to mount a bad drive num)
-57 noMacDskErr not a mac diskette (sig bytes are wrong)
-58 extFSErr External file system - file system identifier is nonzero
-59 fsRnErr file system internal error: during rename the old entry was deleted but could not be restored*
-60 badMDBErr bad master directory block
-61 wrPermErr Write permissions error; Not a publisher

Font Manager Errors -64 fontDecError error during font declaration
-65 fontNotDeclared font not declared
-66 fontSubErr font substitution occured

Disk, Serial Ports, Clock Specific Errors -64 lastDskErr

-64 noDriveErr drive not installed
-65 offLinErr r/w requested for an off-line drive
-66 noNybErr couldn't find 5 nybbles in 200 tries
-67 noAdrMkErr couldn't find valid addr mark
-68 dataVerErr read verify compare failed
-69 badCksmErr addr mark checksum didn't check
-70 badBtSlpErr bad addr mark bit slip nibbles
-71 noDtaMkErr couldn't find a data mark header
-72 badDCksum bad data mark checksum
-73 badDBtSlp bad data mark bit slip nibbles
-74 wrUnderrun write underrun occurred
-75 cantStepErr step handshake failed
-76 tk0BadErr track 0 detect doesn't change
-77 initIWMErr unable to initialize IWM
-78 twoSideErr tried to read 2nd side on a 1-sided drive
-79 spdAdjErr unable to correctly adjust disk speed
-80 seekErr track number wrong on address mark
-81 sectNFErr sector number never found on a track
-82 fmt1Err can't find sector 0 after track format
-83 fmt2Err can't get enough sync
-84 verErr track failed to verify
-84 firstDskErr

-85 clkRdErr unable to read same clock value twice
-86 clkWrErr time written did not verify
-87 prWrErr parameter ram written didn't read-verify
-88 prInitErr InitUtil found the parameter ram uninitialized
-89 rcvrErr SCC receiver error (framing, parity, OR)
-90 breakRecd Break received (SCC)

AppleTalk Errors -91 ddpSktErr Error opening socket OR
-91 eMultiErr Invalid address or table is full
-92 ddpLenErr Data length too big OR
-92 eLenErr Packet too large or first entry of the write-data structure did not contain the full 14-byte header
-93 noBridgeErr No router available [for non-local send]
-94 lapProtErr error in attaching/detaching protocol OR
-94 LAPProtErr Protocol handler is already attached, node's protocol table is full, protocol not attached, or protocol handler pointer was not 0
-95 excessCollsns Hardware error [excessive collisions on write]
-97 portInUse driver Open error code (port is in use)
-98 portNotCf driver Open error code (parameter RAM not configured for this connection)
-99 memROZErr hard error in ROZ
-99 memROZError hard error in ROZ
-99 memROZWarn soft error in ROZ

Scrap Manager Errors -100 noScrapErr No scrap exists error
-102 noTypeErr Format not available [no object of that type in scrap]

Storage Allocator Errors -108 memFullErr Ran out of memory [not enough room in heap zone]
-109 nilHandleErr GetHandleSize fails on baseText or substitutionText; NIL master pointer [handle was NIL in HandleZone or other]
-110 memAdrErr Address was odd, or out of range
-111 memWZErr Attempted to operate on a free block; GetHandleSize fails on baseText or substitutionText [WhichZone failed (applied to free block)]
-112 memPurErr Trying to purge a locked or non-purgeable block
-113 memAZErr Address in zone check failed
-114 memPCErr Pointer Check failed
-115 memBCErr Block Check failed
-116 memSCErr Size Check failed
-117 memLockedErr Trying to move a locked block (MoveHHi)

HFS Errors -120 dirNFErr Directory not found
-121 tmwdoErr No free WDCB available
-122 badMovErr Move into offspring error
-123 wrgVolTypErr Not an HFS volume [wrong volume type error or (obsolete) operation not supported for MFS]
-124 volGoneErr Server volume has been disconnected.
-125 updPixMemErr Insufficient memory to update a pixmap
-127 fsDSIntErr Internal file system error

Menu Manager Errors -126 dsMBarNFnd System error code for MBDF not found
-127 dsHMenuFindErr Could not find HMenu's parent in MenuKey
-128 userCanceledErr User canceled an operation

HFS FileID Errors -130 fidNotFound no file thread exists
-131 fidNotAFile directory specified
-132 fidExists file id already exists

Color Quickdraw and Color Manager Errors -147 regionTooBigError Region too big or complex
-148 pixMapTooBigErr Pixel map record is deeper than 1 bit per pixel [passed pixelmap is too large]
-149 notEnoughStack Not enough stack space for the necessary buffers OR
-149 mfStackErr Insufficient stack
-150 cMatchErr Color2Index failed to find an index
-151 cTempMemErr Failed to allocate memory for temporary structures
-152 cNoMemErr Failed to allocate memory for structure
-153 cRangeErr Range error on colorTable request
-154 cProtectErr ColorTable entry protection violation
-155 cDevErr Invalid type of graphics device
-156 cResErr Invalid resolution for MakeITable
-157 cDepthErr Invalid pixel depth
-158 cParmErr Invalid parameter

Resource Manager Errors (other than I/O) -185 badExtResource Extended resource has a bad format.
-186 CantDecompress Resource bent ("the bends") can't decompress a compressed resource
-188 resourceInMemory Resource already in memory
-189 writingPastEnd Writing past end of file
-190 inputOutOfBounds Offset or count out of bounds
-192 resNotFound Resource not found
-193 resFNotFound Resource file not found
-194 addResFailed AddResource failed
-195 addRefFailed AddReference failed
-196 rmvResFailed RmveResource failed
-197 rmvRefFailed RmveReference failed
-198 resAttrErr Attribute inconsistent with operation
-199 mapReadErr Map inconsistent with operation

Sound Manager Errors -200 noHardware Required sound hardware not available [no hardware support for the specified synthesizer]
-201 notEnoughHardware Insufficient hardware available [no more channels for the specified synthesizer]
-203 queueFull No room in the queue
-204 resProblem Problem loading the resource
-205 badChannel Channel is corrupt or unusable [invalid channel queue length]
-206 badFormat Resource is corrupt or unusable [handle to 'snd ' resource was invalid]
-207 notEnoughBufferSpace Insufficient memory available
-208 badFileFormat File is corrupt or unusable, or not AIFF or AIFF-C
-209 channel Channel is busy
-210 buffersTooSmall Buffer is too small
-211 channelNotBusy Channel not currently used
-212 noMoreRealTime Not enough CPU time available
-213 badParam A parameter is incorrect
-220 siNoSoundInHardware No sound input hardware available
-221 siBadSoundInDevice Invalid sound input device
-222 siNoBufferSpecified No buffer specified
-223 siInvalidCompression Invalid compression type
-224 siHardDiskTooSlow Hard drive too slow to record
-225 siInvalidSampleRate Invalid sample rate
-226 siInvalidSampleSize Invalid sample size
-227 siDeviceBusyErr Sound input device is busy
-228 siBadDeviceName Invalid device name
-229 siBadRefNum Invalid reference number
-230 siInputDeviceErr Input device hardware failure
-231 siUnknownInfoType Unknown type of information
-232 siUnknownQuality Unknown quality

MIDI Manager Errors -250 midiNoClientErr no client with that ID found
-251 midiNoPortErr no port with that ID found
-252 midiTooManyPortsErr too many ports already installed in the system
-253 midiTooManyConsErr too many connections made
-254 midiVConnectErr pending virtual connection created
-255 midiVConnectMade pending virtual connection resolved
-256 midiVConnectRmvd pending virtual connection removed
-257 midiNoConErr no connection exists between specified ports
-258 midiWriteErr couldn't write to all connected ports
-259 midiNameLenErr name supplied is longer than 31 characters
-260 midiDupIDErr duplicate client ID
-261 midiInvalidCmdErr command not supported for port type


Related Documents

9804 Mac OS System Error Codes: -299 to -5553
9806 Mac OS System Error Codes: 1 to 32467

This thread has been closed by the system or the community team. You may vote for any posts you find helpful, or search the Community for additional answers.

Error type 127

Welcome to Apple Support Community
A forum where Apple customers help each other with their products. Get started with your Apple Account.