Safari is crashing my computer

Please read this whole message before doing anything.

This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.

The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.

Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem.

Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.

Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.

The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.

Test while in safe mode. Same problem?

After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Try a restart.

Do a backup, using either Time Machine or a cloning program, to ensure files/data can be recovered. Two backups are better than one.

Try setting up another admin user account to see if the same problem continues. If Back-to-My Mac is selected in System Preferences, the Guest account will not work. The intent is to see if it is specific to one account or a system wide problem. This account can be deleted later.

Isolating an issue by using another user account

Try uninstalling Java as a test.

Java 8 install/un-install

These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.

Launch the Console application in any of the following ways:

☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)

☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.

☞ Open LaunchPad and start typing the name.

Step 1

For this step, the title of the Console window should be All Messages. If it isn't, select

SYSTEM LOG QUERIES ▹ All Messages

from the log list on the left. If you don't see that list, select

View ▹ Show Log List

from the menu bar at the top of the screen.

In the top right corner of the Console window, there's a search box labeled Filter. Enter "BOOT_TIME" (without the quotes.)

Each message in the log begins with the date and time when it was entered. Select the BOOT_TIME log message that corresponds to the last boot time when you had the problem. Now clear the search box to reveal all messages. Select the ones logged before the boot, during the time something abnormal was happening. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.

For example, if the system was unresponsive or was failing to shut down for three minutes before you forced a restart, post the messages timestamped within three minutes before the boot time, not after. Please include the BOOT_TIME message at the end of the log extract—not at the beginning.

If there are long runs of repeated messages, please post only one example of each. Don’t post many repetitions of the same message.

When posting a log extract, be selective. A few dozen lines are almost always more than enough.

Some private information, such as your name, may appear in the log. Anonymize before posting.

Please don't indiscriminately dump thousands of lines from the log into this discussion.

Please don't post screenshots of log messages—post the text.

Step 2

In the Console window, select

DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports

(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select

View ▹ Show Log List

from the menu bar.

There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A crash report has a name that begins with the name of the crashed process and ends in ".crash". A panic report has a name that begins with "Kernel" and ends in ".panic". A shutdown stall report has a name that ends in ".shutdownstall". Select the most recent of each, if any. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot. It's possible that none of these reports exists.

I know the report is long, maybe several hundred lines. Please post all of it anyway.

If you don't see any reports listed, but you know there was a crash or panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.

In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)

Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

When you post the log extract or the crash report, you might see an error message on the web page: "You have included content in your post that is not permitted," or "The message contains invalid characters." That's a bug in the forum software. Please post the text on Pastebin, then post a link here to the page you created.

Did you try setting up another admin account? The link opens for me.