Oh No Kernal Panic again for my new hard drive!

Hey There the restart automatically because the computer is having problem for Kernal Panic also I send the Apple! Thank you please fix it!

iMac 27", macOS 10.13

Posted on Apr 18, 2020 8:58 PM

Similar questions

"The file can't be found." on booting... Everytime I start my MacBook Pro (intel chip), I get two error message. Both say "The file can't be found". This has been happening ever since I updated to big sur. I have to click on "OK" (twice) to make them go away. Neither does it tell you what file can't be found. I just updated to Ventura 13.1 and the problem remains. As does the control strip/touch bar issue. Is Apple going downhill...SMH.
1892 2
Boot problem MacBook Pro A1990 Good morning everyone, I am writing to you because I have a problem with a MacBook Pro Model A1990. When turn on the pc appear this screen If I tried to enter in recovery mode: this is the result: I tried olso with a bootable USB with macOS Ventura but is not possibile select... I have tried to reset nvrm, following general procedures on youtube but nothing. In my opinion the SSD is damage, should this possible? Thank you for your support. Regards
5196 17
Is it normal to have so many access denied errors due to sandbox for apple system processes? I just did a clean install Ventur and am getting a lot of access denied errors reported for system processes. The clean install involved reformatting the entire internal SSD by choosing the device, not the volumes and then installing from a bootable USB, although I didn't actually boot from the USB, I just did it while I was in Recovery after reformatting the disk - but used the USB files (which I had just created using the create bootable installer tool in the Ventura 13.1 app itself). Is this normal? The error rate is really fast, and at times the fault rate for various system processes is, as well. I'm concerned that either the Mac itself is a lemon, or Ventura is. I should point out that this is a MacBook Pro 14" 18,4 - the 10 cpu/24 gpu M1, with 64 gb memory and a 2 TB drive. I have had various problems - it's now been 48 hours since the install and the battery isn't using optimal charging yet, as it should be by now. I think it is turned on - at least system settings says it is, but cfprefsd is one of the process getting sandbox errors when trying to read my preferences and at least in the case of Allow Remote Access, I had to toggle the switch a couple of times before sshd actually ran. Changing the computer name also seemed to take a while to display correctly, I had to keep changing it back to my desired name because it would revert to the default name. I'm not sure if the Systems Setting is displaying the actual state of various options because of that. This is a MacBook Pro 18,4, with the 10 cpu/24 gpu M1, 64 gb memory and a 2 TB drive.
4822 7

5 replies

babowa

Level 9

78,586 points

Apr 18, 2020 10:35 PM in response to Lerdalparker23

We are all other users here and cannot fix kernel panics. Please post exact model/year and info about the new hard drive. Who installed it? What brand is it? Was it installed correctly?

babowa

Level 9

78,586 points

Apr 19, 2020 10:39 AM in response to Lerdalparker23

Can't answer that unless you answer my questions regarding the hard drive.

Kernel panics are not ok; usually a hardware problem, so you need to figure out why you had the kernel panic.

Apr 18, 2020 10:51 PM in response to babowa

iMac Mid 2011 inch

babowa

Level 9

78,586 points

Apr 19, 2020 9:13 AM in response to Lerdalparker23

And what about the hard drive? And the thermal sensor?

Apr 19, 2020 9:50 AM in response to babowa

Yes I know I went on a computer I had a serious problem the computer is automatically restart it says your computer is problem because it was a restart for Kernel Panic okay?

This thread has been closed by the system or the community team. You may vote for any posts you find helpful, or search the Community for additional answers.

Oh No Kernal Panic again for my new hard drive!