i loaned my macbook pro to a friend. when i got it back i wanted to wipe it so followed the process on line. now when i start it, the globe spins and the stops, has an exclamation point in the middle and error code -2003F. wont move from that

what is error code -2003F

Posted on Aug 12, 2021 12:00 AM

Similar questions

"The file can't be found." on booting... Everytime I start my MacBook Pro (intel chip), I get two error message. Both say "The file can't be found". This has been happening ever since I updated to big sur. I have to click on "OK" (twice) to make them go away. Neither does it tell you what file can't be found. I just updated to Ventura 13.1 and the problem remains. As does the control strip/touch bar issue. Is Apple going downhill...SMH.
2599 2
Errors while updating from 11.7.2 Big Sur to Ventura 13.1 or Monterey 12.1 macOS Big Sur Version 11.7.2 MacBook Pro (16-inch, 2019) 2.6 GHz 6-core Intel Core i7 16 GB 2667 MHz DDR4 Intel UHD Graphics 630 1536 MB I have been trying to complete the newest software update. I have not been updating regularly which I am assuming may be one of my problems. I tried to upgrade to macOS Ventura 13.1, which is what shows when I got to software update in system preferences. I get this error every time I attempt the upgrade. I have restarted, restarted in safe mode, as well as tried to reinstall the Mac OS from recovery mode. None of it works. Always the same result. I have used WiFi and ethernet. I've scoured this board to try and find a fix. When I am try it in recovery mode it gives me this status bar screen: But doesn't move from that. It stays "about 2 hours and 21 minutes remaining" for about 20 minutes and then it gives me this error: I tried to move from Big Sur to Monterey thinking that perhaps I needed to go from 11 to 12 before 13. This is the error I get when I try to upgrade to Monterey: “The operation couldn’t be completed. (PKDownloadError error 8.)" I'm not sure what is wrong and I would love any advice on how to fix this. I appreciate any help! Thanks!
4346 19
Is it normal to have so many access denied errors due to sandbox for apple system processes? I just did a clean install Ventur and am getting a lot of access denied errors reported for system processes. The clean install involved reformatting the entire internal SSD by choosing the device, not the volumes and then installing from a bootable USB, although I didn't actually boot from the USB, I just did it while I was in Recovery after reformatting the disk - but used the USB files (which I had just created using the create bootable installer tool in the Ventura 13.1 app itself). Is this normal? The error rate is really fast, and at times the fault rate for various system processes is, as well. I'm concerned that either the Mac itself is a lemon, or Ventura is. I should point out that this is a MacBook Pro 14" 18,4 - the 10 cpu/24 gpu M1, with 64 gb memory and a 2 TB drive. I have had various problems - it's now been 48 hours since the install and the battery isn't using optimal charging yet, as it should be by now. I think it is turned on - at least system settings says it is, but cfprefsd is one of the process getting sandbox errors when trying to read my preferences and at least in the case of Allow Remote Access, I had to toggle the switch a couple of times before sshd actually ran. Changing the computer name also seemed to take a while to display correctly, I had to keep changing it back to my desired name because it would revert to the default name. I'm not sure if the Systems Setting is displaying the actual state of various options because of that. This is a MacBook Pro 18,4, with the 10 cpu/24 gpu M1, 64 gb memory and a 2 TB drive.
5189 7

3 replies

Sharhari

Level 5

6,313 points

Aug 12, 2021 12:54 AM in response to SMKEN007

It could be an issue with connecting to Apple recovery through internet. See if you can change your network connection / try connect via cable/ethernet if possible.

Some times Reseting NVRAM can also help.

SMKEN007 Author

Level 1

4 points

Aug 12, 2021 12:53 AM in response to SMKEN007

and now have error 1005F

SMKEN007 Author

Level 1

4 points

Aug 12, 2021 1:08 AM in response to Sharhari

you are a legend!!! that worked - i plugged cable in and it worked - thank you so very much!!

This thread has been closed by the system or the community team. You may vote for any posts you find helpful, or search the Community for additional answers.

i loaned my macbook pro to a friend. when i got it back i wanted to wipe it so followed the process on line. now when i start it, the globe spins and the stops, has an exclamation point in the middle and error code -2003F. wont move from that