smartctl 6.5 2016-05-07 r4318 [Darwin 15.6.0 x86_64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K320
Device Model: Hitachi HTS543225L9SA02
Serial Number: 081028FB1F00LLJ4Z4VF
LU WWN Device Id: 5 000cca 55fde71b2
Firmware Version: FBEAC50F
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 3f
SATA Version is: SATA 2.6, 1.5 Gb/s
Local Time is: Sat Nov 18 11:43:23 2017 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 102) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 253 253 033 Pre-fail Always - 0
4 Start_Stop_Count 0x0012 076 076 000 Old_age Always - 38002
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 50
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 029 029 000 Old_age Always - 31342
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 093 093 000 Old_age Always - 12460
160 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 1382979469312
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 184688705697
193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 2640835
194 Temperature_Celsius 0x0002 141 141 000 Old_age Always - 39 (Min/Max 4/47)
195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 50
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 5
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 092 092 000 Old_age Always - 2122
SMART Error Log Version: 1
ATA Error Count: 1004 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1004 occurred at disk power-on lifetime: 31341 hours (1305 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 dd 93 bc 4b 40 Error: UNC 221 sectors at LBA = 0x004bbc93 = 4963475
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 70 bc 4b 40 00 01:21:45.500 READ DMA EXT
25 00 00 70 bc 4b 40 00 01:21:41.100 READ DMA EXT
ef 10 02 00 00 00 00 00 01:21:41.100 SET FEATURES [Enable SATA feature]
ef 02 00 00 00 00 00 00 01:21:41.100 SET FEATURES [Enable write cache]
ef aa 00 00 00 00 00 00 01:21:41.100 SET FEATURES [Enable read look-ahead]
Error 1003 occurred at disk power-on lifetime: 31341 hours (1305 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 dd 93 bc 4b 40 Error: UNC 221 sectors at LBA = 0x004bbc93 = 4963475
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 70 bc 4b 40 00 01:21:41.100 READ DMA EXT
ef 10 02 00 00 00 00 00 01:21:41.100 SET FEATURES [Enable SATA feature]
ef 02 00 00 00 00 00 00 01:21:41.100 SET FEATURES [Enable write cache]
ef aa 00 00 00 00 00 00 01:21:41.100 SET FEATURES [Enable read look-ahead]
ef 03 46 00 00 00 00 00 01:21:41.100 SET FEATURES [Set transfer mode]
Error 1002 occurred at disk power-on lifetime: 31341 hours (1305 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 dd 93 bc 4b 40 Error: UNC 221 sectors at LBA = 0x004bbc93 = 4963475
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 70 bc 4b 40 00 01:21:09.000 READ DMA EXT
25 00 00 70 bc 4b 40 00 01:21:04.900 READ DMA EXT
25 00 10 b0 fb 3c 40 00 01:21:04.900 READ DMA EXT
25 00 10 f0 1a 1f 40 00 01:21:04.900 READ DMA EXT
25 00 00 70 bc 4b 40 00 01:21:00.800 READ DMA EXT
Error 1001 occurred at disk power-on lifetime: 31341 hours (1305 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 dd 93 bc 4b 40 Error: UNC 221 sectors at LBA = 0x004bbc93 = 4963475
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 70 bc 4b 40 00 01:21:04.900 READ DMA EXT
25 00 10 b0 fb 3c 40 00 01:21:04.900 READ DMA EXT
25 00 10 f0 1a 1f 40 00 01:21:04.900 READ DMA EXT
25 00 00 70 bc 4b 40 00 01:21:00.800 READ DMA EXT
2f 00 01 10 00 00 00 00 01:21:00.800 READ LOG EXT
Error 1000 occurred at disk power-on lifetime: 31341 hours (1305 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 dd 93 bc 4b 40 Error: UNC 221 sectors at LBA = 0x004bbc93 = 4963475
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 70 bc 4b 40 00 01:21:00.800 READ DMA EXT
2f 00 01 10 00 00 00 00 01:21:00.800 READ LOG EXT
60 10 10 b0 fb 3c 40 00 01:20:56.800 READ FPDMA QUEUED
60 10 08 f0 1a 1f 40 00 01:20:56.800 READ FPDMA QUEUED
60 00 00 70 bc 4b 40 00 01:20:56.800 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.